Lenovo HX3510-G Installation And Service Manual Download Page 866

Page: 866 / 1240

1. (Trained technician only) Replace microprocessor n (see Removing a microprocessor and heat

sink and Replacing a microprocessor and heat sink).

2. If the problem persists and there is no other CPU with the same error indication, replace the

system board.

3. (Trained technician only) Replace the system board (see Removing the system board and

Replacing the system board). (n = microprocessor number)

•

816f0113-0302ffff : System [ComputerSystemElementName] has recovered from a bus timeout.

(CPU 2 PECI)

This message is for the use case when an implemenation has detected that a system has recovered from
a Bus Timeout.

May also be shown as 816f01130302ffff or 0x816f01130302ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0225

User Response

1. (Trained technician only) Replace microprocessor n (see Removing a microprocessor and heat

sink and Replacing a microprocessor and heat sink).

2. If the problem persists and there is no other CPU with the same error indication, replace the

system board.

3. (Trained technician only) Replace the system board (see Removing the system board and

Replacing the system board). (n = microprocessor number)

•

816f011b-0701ffff : The connector [PhysicalConnectorElementName] configuration error has

been repaired. (Front USB)

This message is for the use case when an implementation has detected an Interconnect Configuration
was Repaired.

May also be shown as 816f011b0701ffff or 0x816f011b0701ffff

854

HX3510-G, HX5510, HX5510-C, HX7510 Installation and Service Guide

Summary of Contents for HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands

Lenovo HX3510-G, Installation And Service Manual

Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands