Lenovo HX3510-G Installation And Service Manual Download Page 793

Page: 793 / 1240

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0523

User Response

No action; information only.

•

8107021b-0302ffff : Sensor [SensorElementName] has transitioned to a less severe state from

critical. (CPU 2 QPILinkErr)

This message is for the use case when an implementation has detected a Sensor transition to less
severe from critical.

May also be shown as 8107021b0302ffff or 0x8107021b0302ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0523

User Response

No action; information only.

•

81070228-2e01ffff : Sensor [SensorElementName] has transitioned to a less severe state from

critical. (ME Error)

This message is for the use case when an implementation has detected a Sensor transition to less
severe from critical.

May also be shown as 810702282e01ffff or 0x810702282e01ffff

Appendix A. Integrated management module II (IMM2) error messages

781

Summary of Contents for HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands

Lenovo HX3510-G, Installation And Service Manual

Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands