Lenovo HX3510-G Installation And Service Manual Download Page 380

Page: 380 / 1240

Severity

Error

Serviceable

Yes

Automatically notify support

Alert Category

Critical - Temperature

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0494

User Response

1. Reduce the ambient temperature.

2. Ensure the air baffle is installed correctly.

3. Check the server airflow. Make sure that nothing is blocking the air from coming into or

preventing the air from exiting the server.

•

80010901-1405ffff : Numeric sensor [NumericSensorElementName] going high (upper critical)

has asserted. (DIMM EF VR Temp)

This message is for the use case when an implementation has detected an Upper Critical sensor going
high has asserted.

May also be shown as 800109011405ffff or 0x800109011405ffff

Severity

Error

Serviceable

Yes

Automatically notify support

Alert Category

Critical - Temperature

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0494

User Response

1. Reduce the ambient temperature.

2. Ensure the air baffle is installed correctly.

368

HX3510-G, HX5510, HX5510-C, HX7510 Installation and Service Guide

Summary of Contents for HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands

Lenovo HX3510-G, Installation And Service Manual

Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands