Lenovo HX3510-G Installation And Service Manual Download Page 1093

Page: 1093 / 1240

Severity

Warning

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Remove power cables, wait for 45 seconds, reconnect and rerun the test.

2. Make sure that the scalability cable connections are as per specification.

3. Make sure that DSA and BIOS/uEFI are at the latest level.

4. If the problem remains, contact your technical-service representative.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

401-901-001 : EXA Port Ping Test Failed

EXA Port Ping Test Failed.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Remove power cables, wait for 45 seconds, reconnect and rerun the test.

2. Make sure that the scalability cable connections are as per specification.

3. Check scalability cables for loose connections.

4. Replace the scalability cable(s) for specified port(s).

5. If the problem remains, contact your technical-service representative.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

Appendix C. DSA diagnostic test results

1081

«
...
1091
1092
1093
1094
1095
...
»

Summary of Contents for HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands

Lenovo HX3510-G, Installation And Service Manual

Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands