Lenovo HX3510-G Installation And Service Manual Download Page 871

Page: 871 / 1240

Automatically notify support

Alert Category

Critical - CPU

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0045

User Response

No action; information only.

•

816f0207-0302ffff : [ProcessorElementName] has Recovered from FRB1/BIST condition. (CPU 2)

This message is for the use case when an implementation has detected a Processor Recovered -
FRB1/BIST condition.

May also be shown as 816f02070302ffff or 0x816f02070302ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - CPU

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0045

User Response

No action; information only.

•

816f0207-2584ffff : [ProcessorElementName] has Recovered from FRB1/BIST condition. (All CPUs)

This message is for the use case when an implementation has detected a Processor Recovered -
FRB1/BIST condition.

May also be shown as 816f02072584ffff or 0x816f02072584ffff

Severity

Info

Serviceable

Appendix A. Integrated management module II (IMM2) error messages

859

Summary of Contents for HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands

Lenovo HX3510-G, Installation And Service Manual

Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands