Lenovo HX3510-G Installation And Service Manual Download Page 1106

Page: 1106 / 1240

–

Latest level of DSA

–

Latest level of BMC/IMM

•

408-901-000 : MLNX:MLNX_DiagnosticTestIBPort Test Failed

Port Test Failed.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Make sure that the physical link of the port under test in the active state and a subnet manager

running on the fabric to which the port is attached.

2. If these condition was met but the test keeps failing the port's adapter might be faulty.

3. Try replacing the adapter and repeating the test.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

DSA memory isolation test results

The following messages can result when you run the memory isolation test.

Test results for the DSA memory isolation test

The following messages can result when you run the DSA memory isolation test.

•

201-000-000 : Standalone Memory Test Passed

Quick/Full Memory Test All CPUs Passed.

Recoverable

Severity

Event

Serviceable

1094

HX3510-G, HX5510, HX5510-C, HX7510 Installation and Service Guide

«
...
1104
1105
1106
1107
1108
...
»

Summary of Contents for HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands

Lenovo HX3510-G, Installation And Service Manual

Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands