Lenovo HX3510-G Installation And Service Manual Download Page 1048 | Manualshive

Page: 1048 / 1240

background image

•

S.2018001 An Uncorrected PCIe Error has Occurred at Bus [arg1] Device [arg2] Function [arg3].

The Vendor ID for the device is [arg4] and the Device ID is [arg5]. PCIe Uncorrected Error Detected

Explanation:

Severity

Error

User Response

Complete the following steps:

1. Check IBM support site for an applicable device driver, firmware update, version of service

information for this product or other information that applies to this error. Load new device driver
and any required firmware updates.

2. If this node and/or any attached cables were recently installed, moved, serviced or upgraded, a.

Reseat Adapter and any attached cables. b. Reload Device Driver c. If device is not recognized,
reconfiguring slot to Gen1 or Gen2 may be required. Gen1/Gen2 settings can be configured
via F1 Setup -> System Settings -> Devices and I/O Ports -> PCIe Gen1/Gen2/Gen3 Speed
Selection, or the ToolsCenter Suite CLI Utility.

3. If problem persists, then remove Adapter Card. If system reboots successfully without the

adapter, replace that card.

4. (Trained Service technician only) Replace the system board.

5. (Trained Service technician only) Replace the processor.

•

S.3020007 A firmware fault has been detected in the UEFI image. Internal UEFI Firmware Fault

Detected, System halted

Explanation:

Severity

Error

User Response

Complete the following steps:

1. Check the IBM support site for an applicable service bulletin or firmware update that applies to

this error.

2.

Update the UEFI image.

3. (Trained service technician only) Replace the system board.

•

S.3028002 Boot permission timeout detected. Boot Permission Negotiation Timeout

Explanation:

Severity

Error

User Response

Complete the following steps:

1. Check CMM/IMM logs for communication errors and resolve.

2.

Reseat the system

3. If problem persists contact support

1036

HX3510-G, HX5510, HX5510-C, HX7510 Installation and Service Guide

«
...
1046
1047
1048
1049
1050
...
»

Summary of Contents for HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for HX3510-G

Brand: NEC Pages: 151

SUPERSERVER 5018D-MHR7N4P

Brand: Supermicro Pages: 126

Flex System x240 Compute Node

Brand: IBM Pages: 28

Brand: Oki Pages: 2

TJA670 domovea Basic

Brand: hager Pages: 36

Brand: ImageTech Pages: 44

SUPERSERVER 5018A-MHN4

Brand: Supermicro Pages: 116

Brand: HPE Pages: 58

DLAP-201 Series

Brand: ADLINK Technology Pages: 39

Brand: AC&T System Pages: 32

Brand: Waves Pages: 6

Flex System x240

Brand: Lenovo Pages: 42

Advanced Office-in-a-Box

Brand: Enconnex Pages: 40

Brand: Aviosys Pages: 30

Brand: XtendLan Pages: 50

Brand: RoviSys Pages: 146

Brand: Tatung Pages: 35

Brand: IBM Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands