Lenovo HX3510-G Installation And Service Manual Download Page 1094

Page: 1094 / 1240

DSA hard drive test results

The following messages can result when you run the hard drive test.

Test results for the DSA hard drive test

The following messages can result when you run the DSA hard drive test.

•

217-000-000 : HDD Test Passed

HDD Stress Test Passed.

Recoverable

Severity

Event

Serviceable

Automatically notify support

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

217-800-000 : HDD Test Aborted

HDD Test Aborted. The test was canceled.

Recoverable

Severity

Warning

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Check cable connections.

2. Rerun the test.

3. Verify that Hard drive supports self test and self test logging.

4. If the problem remains, contact your technical-support representative.

Related links

1082

HX3510-G, HX5510, HX5510-C, HX7510 Installation and Service Guide

«
...
1092
1093
1094
1095
1096
...
»

Summary of Contents for HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands

Lenovo HX3510-G, Installation And Service Manual

Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands