Lenovo HX3510-G Installation And Service Manual Download Page 919

Page: 919 / 1240

Alert Category

System - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0130

User Response

No action; information only.

•

816f040c-2003ffff : [PhysicalMemoryElementName] Enabled on Subsystem

[MemoryElementName]. (DIMM 3)

This message is for the use case when an implementation has detected that Memory has been Enabled.

May also be shown as 816f040c2003ffff or 0x816f040c2003ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

System - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0130

User Response

No action; information only.

•

816f040c-2004ffff : [PhysicalMemoryElementName] Enabled on Subsystem

[MemoryElementName]. (DIMM 4)

This message is for the use case when an implementation has detected that Memory has been Enabled.

May also be shown as 816f040c2004ffff or 0x816f040c2004ffff

Severity

Info

Serviceable

Automatically notify support

Appendix A. Integrated management module II (IMM2) error messages

907

Summary of Contents for HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands

Lenovo HX3510-G, Installation And Service Manual

Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands