Lenovo HX3510-G Installation And Service Manual Download Page 1056

Page: 1056 / 1240

Explanation:

Severity

Warning

User Response

Complete the following steps:

Go to F1 Setup > System Settings > Settings > Driver Health Status List and find a

driver/controller reporting Configuration Required status.

2. Search for the driver menu from System Settings and change settings appropriately.

3. Save settings and restart system.

•

W.305800A DRIVER HEALTH PROTOCOL: Reports 'Failed' Status Controller. DRIVER HEALTH

PROTOCOL: Reports 'Failed' Status Controller

Explanation:

Severity

Warning

User Response

Complete the following steps:

Reboot the system.

2. If problem persists, switch to backup UEFI or update the current UEFI image.

Replace the system board.

•

W.305800B DRIVER HEALTH PROTOCOL: Reports 'Reboot' Required Controller. DRIVER HEALTH

PROTOCOL: Reports 'Reboot' Required Controller

Explanation:

Severity

Warning

User Response

Complete the following steps:

1. No action required. The system will reboot at the end of POST.

2. If the problem persists, switch to the backup UEFI image or update the current UEFI image.

Replace the system board.

•

W.305800C DRIVER HEALTH PROTOCOL: Reports 'System Shutdown' Required Controller.

DRIVER HEALTH PROTOCOL: Reports 'System Shutdown' Required Controller

Explanation:

Severity

Warning

User Response

Complete the following steps:

1044

HX3510-G, HX5510, HX5510-C, HX7510 Installation and Service Guide

«
...
1054
1055
1056
1057
1058
...
»

Summary of Contents for HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands

Lenovo HX3510-G, Installation And Service Manual

Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands