Lenovo HX3510-G Installation And Service Manual Download Page 833

Page: 833 / 1240

Prefix:

PLAT

ID:

0331

User Response

No action; information only. One of PCI Error :

•

816f0021-2c01ffff : Fault condition removed on slot [PhysicalConnectorElementName] on system

[ComputerSystemElementName]. (ML2 Card Fault)

This message is for the use case when an implementation has detected a Fault condition in a slot has
been removed.

May also be shown as 816f00212c01ffff or 0x816f00212c01ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0331

User Response

No action; information only.

•

816f0021-3001ffff : Fault condition removed on slot [PhysicalConnectorElementName] on system

[ComputerSystemElementName]. (Internal RAID)

This message is for the use case when an implementation has detected a Fault condition in a slot has
been removed.

May also be shown as 816f00213001ffff or 0x816f00213001ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Other

SNMP Trap ID

Appendix A. Integrated management module II (IMM2) error messages

821

Summary of Contents for HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands

Lenovo HX3510-G, Installation And Service Manual

Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands