Lenovo HX3510-G Installation And Service Manual Download Page 255

Page: 255 / 1240

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0008

User Response

Information only; no action is required.

•

40000009-00000000 : IP address of network interface modified from [arg1] to [arg2] by user [arg3].

This message is for the use case where user modifies the IP address of a Management Controller.

May also be shown as 4000000900000000 or 0x4000000900000000

Severity

Info

Serviceable

Automatically notify support

Alert Category

System - IMM Network event

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0009

User Response

Information only; no action is required.

•

4000000a-00000000 : IP subnet mask of network interface modified from [arg1] to [arg2] by user

[arg3].

This message is for the use case where a user modifies the IP subnet mask of a Management Controller.

May also be shown as 4000000a00000000 or 0x4000000a00000000

Severity

Info

Serviceable

Automatically notify support

Alert Category

none

SNMP Trap ID

Appendix A. Integrated management module II (IMM2) error messages

243

Summary of Contents for HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands

Lenovo HX3510-G, Installation And Service Manual

Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands