Lenovo HX3510-G Installation And Service Manual Download Page 214

Page: 214 / 1240

Snaps

Hooks

Figure 157. Hooks (the rear side of the media cage)

11. Rotate the media cage bezel and snap it into place.

Media cage

Media cage bezel

Figure 158. Retention bracket installation

12. Install the media cage (see “Replacing the media cage (also called lightpath LCD operation panel

assembly)” on page 141).

13. Replace the top cover (see “Replacing the top cover” on page 118).

14. Slide the server into the rack.

15. Reconnect the power cords and any cables that you removed.

16. Turn on the peripheral devices and the server.

Removing the operator information panel assembly

Use this information to remove the operator information panel assembly.

To remove the operator information panel, complete the following steps.

Step 1.

Read the safety information that begins on “Safety” on page v and “Removing and replacing
guidelines” on page 101.

202

HX3510-G, HX5510, HX5510-C, HX7510 Installation and Service Guide

Summary of Contents for HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands

Lenovo HX3510-G, Installation And Service Manual

Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands