Lenovo HX3510-G Installation And Service Manual Download Page 1050 | Manualshive

Page: 1050 / 1240

background image

Severity

Error

User Response

Complete the following steps:

1. This event resets UEFI to the default settings for the next boot. If successful, the Setup Utility is

displayed. The original UEFI settings are still present.

2. If you did not intentionally trigger the reboots, check logs for probable cause.

3. Undo recent system changes (settings or devices added). If there were no recent system

changes, remove all options, and then remove the CMOS battery for 30 seconds to clear CMOS
contents. Verify that the system boots. Then, re-install the options one at a time to locate the
problem.

4. Check the IBM support site for an applicable service bulletin or firmware update that applies to

this error.

5.

Update the UEFI firmware.

6. Remove and re-install CMOS battery for 30 seconds to clear CMOS contents.

7. (Trained service technician only) Replace the system board.

•

S.3060007 A firmware fault has been detected in the UEFI image. Internal UEFI Firmware Fault

Detected, System halted

Explanation:

Severity

Error

User Response

Complete the following steps:

1. Check IBM support site for an applicable service bulletin or firmware update that applies to

this error.

2.

Update the UEFI image.

3.

Replace the system board.

•

S.3070007 A firmware fault has been detected in the UEFI image. Internal UEFI Firmware Fault

Detected, System halted

Explanation:

Severity

Error

User Response

Complete the following steps:

1. Check IBM support site for an applicable service bulletin or firmware update that applies to

this error.

2.

Update the UEFI image.

3.

Replace the system board.

1038

HX3510-G, HX5510, HX5510-C, HX7510 Installation and Service Guide

«
...
1048
1049
1050
1051
1052
...
»

Summary of Contents for HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for HX3510-G

Redbooks ServeRAID-MR10k

Brand: IBM Pages: 48

Brand: NMS Communications Pages: 22

Brand: Fujitsu Pages: 280

Brand: Generac Power Systems Pages: 52

ANTMINER S19a Pro

Brand: BITMAIN Pages: 17

Brand: Planet Pages: 141

Express5800/140Hf

Brand: NEC Pages: 482

Brand: Abekas Pages: 382

Brand: Abus Pages: 44

Brand: Supero Pages: 106

Brand: Supero Pages: 108

Brand: IBM Pages: 86

Brand: IBM Pages: 90

306m - eServer xSeries - 8849

Brand: IBM Pages: 74

Brand: IBM Pages: 144

Brand: NASdeluxe Pages: 6

Brand: 3onedata Pages: 12

Brand: Intel Pages: 138

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands