Kongsberg Simrad MF90 Installation Manual Download | Manualshive

Page: 335 / 426

background image

476671/B

333

Creating a backup with the MF90 configuration
and software installation

Topics

About MF90 software backup and restore, page 333

Creating a backup image using the desktop application, page 334

Creating a backup image using the boot application, page 336

Restoring from a backup image using the desktop application, page 338

Restoring from a backup image using the boot application, page 340

Creating a bootable USB flash drive, page 343

About MF90 software backup and restore

Once the configuration and testing have been finalized, you must back up the configuration
data and software installation. Your backup will then include the operating system, the
MF90 software, as well as all the interface parameters that you have defined. Software
backup is provided using dedicated software applications and commercial storage devices.

A backup

image

is a very useful feature. It allows you to create and save a complete copy

of all the files on the Processor Unit. Once a backup image exist, you can use it to restore
the entire content of the hard disk in the event of a failure.

The software used is

Acronis True Image

. This application is created by

Acronis

. For more

information about this company and their products, see their website:

•

Manufacturer

: Acronis International GmbH

•

Manufacturer’s website

:

http://www.acronis.com

The backup and restore operations can be done with the following applications:

Boot application

You must use this restore functionality if you are unable to start the Processor Unit
from the C-disk. You need the bootable USB flash drive provided with the MF90
system. You can also use any commercial USB flash drive. It must be formatted as a
bootable device by the Acronis True Image program.

A complete backup requires a large data storage device. A standard USB flash drive
may not have the required storage capacity. You can then use a USB hard disk.

Setting to work

«
...
333
334
335
336
337
...
»

Summary of Contents for Simrad MF90











































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Simrad MF90

Brand: Raytheon Pages: 90

Fishfinder 300 ML

Brand: Garmin Pages: 8

Brand: Lucky Pages: 10

Brand: Lucky Pages: 73

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands