background image

314

476671/B

Testing the operating functionality of the MF90
system

Topics

Checking the hull unit lowering and hoisting functionality, page 314

Verifying system operation by means of the Element BITE functionality, page 319

Measuring the noise in passive mode, page 323

Verifying system operation by means of the Diagnostics functionality, page 325

Making a noise/speed curve to determine vessel noise, page 329

Checking the hull unit lowering and hoisting functionality

The hull unit is used to lower the transducer down below the ship’s hull when the MF90
system shall be used. This is a key functionality of the MF90 system. It is very important
that the hoist/lower function is tested before the MF90 system is put to operational use.

To test the lower and hoist functionality two tasks must be done at the same time.

Two persons are needed.

• One person must stay on the bridge in order to operate the MF90 system.

• One person must stay in the sonar room to make sure that the MF90 system starts, and

that the hull unit works properly.

Proper oral communication must exist between the bridge and the sonar room.

Note

This test can only be done if the water depth allows the transducer to be lowered completely.
If this is not the case, the vessel must be moved to another location, or the test must be
cancelled. Kongsberg Maritime cannot take responsibility for tests that are cancelled for
this reason.

Certain steps in the procedures are location specific. The steps marked [

Sonar room

] are

done in the sonar room. The steps marked [

Bridge

] are done on the bridge.

Simrad MF90 Installation Manual

Summary of Contents for Simrad MF90











































































































































































































































































































































































































































Reviews: