Kongsberg Simrad MF90 Installation Manual Download

Page: 358 / 426

356

476671/B

Operating Panel weight and outline dimensions (Mk3)

•

Make and model

: MF90 Operating Panel Mk3

•

Outline dimensions

–

Depth

: 57 mm

–

Width

: 225 mm

–

Height

: 125 mm

•

Weight

: 0.45 kg (Approximately)

Transceiver Unit weight and outline dimensions

•

Make and model

: MF90 Transceiver Unit

•

Outline dimensions

–

Depth

: 551 mm (With shock absorbers)

–

Width

: 600 mm (Without the large transceiver plug)

–

Height

: 777 mm (With shock absorbers)

•

Weight

: 65 kg (Approximately)

Hull Unit weight and outline dimensions

•

Make

: MF90 Hull Unit

•

Model

: MF90

–

Flange diameter

: 370 mm

–

Number of holes in the flange

: 12

–

Total height

: 2340 mm

–

Height above the installation trunk

: 1390 mm

Simrad MF90 Installation Manual

Summary of Contents for Simrad MF90











































































































































































































































































































































































































































Search results

Summary of Contents for Simrad MF90

Reviews:

Related manuals for Simrad MF90

Brands by name

Popular brands

Kongsberg Simrad MF90, Installation Manual

Search results

Summary of Contents for Simrad MF90

Reviews:

Related manuals for Simrad MF90

Brands by name

Popular brands