Kongsberg Simrad MF90 Installation Manual Download | Manualshive

Page: 28 / 426

background image

26

476671/B

•

Do not

step on the transducer cables.

•

Do not

damage the transducer cables. Avoid exposure to sharp objects.

Related topics

Simrad MF90, page 13
System units, page 20
Installing the hull unit, page 99
Cable layout and interconnections, page 143
Setting to work, page 186
Technical specifications, page 346
Drawing file, page 364

Installation trunk description

An installation trunk is required for hull unit installation. The installation trunk is not
included in the standard delivery.

The installation trunk provides the physical foundation for the entire hull unit. The
installation trunk penetrates the hull. The installation trunk is therefore a crucial part of the
hull unit assembly. In order to ensure proper operation of the MF90 system, the physical
location of the installation trunk must be carefully selected.

The installation trunk - with a blind flange - can be ordered from Kongsberg Maritime as
an optional delivery. As an alternative, the installation trunk can be manufactured by the
shipyard based on the drawings in this manual. A locally manufactured installation trunk
can be adjusted to better fit the properties of the vessel’s hull.

Note

If the installation trunk is manufactured locally, the installation shipyard is responsible for
obtaining the approval certificates from the relevant national registry.

The installation trunk is not used when a gate valve is mounted. The installation trunk is
then replaced with a transducer dock.

Due to the different flange diameters, different installation trunks are used.

Installation trunk

Part number

Upper diameter (mm)

Bottom diameter (mm)

MF90

408615

370

273

427423

760

610

MF94

434529

760

356

Simrad MF90 Installation Manual

«
...
26
27
28
29
30
...
»

Summary of Contents for Simrad MF90











































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Simrad MF90

Brand: Raymarine Pages: 2

Marine Commander MXF-5000

Brand: Icom Pages: 16

Brand: Standard Horizon Pages: 144

Brand: Humminbird Pages: 210

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands