manualshive.com logo in svg

Kongsberg Simrad MF90, Installation Manual

Share
Download
Kongsberg Simrad MF90 Installation Manual Download Page 22

20

476671/B

System units

Topics

Display description, page 20

Processor Unit description, page 21

Transceiver Unit description, page 22

Hull Unit description, page 23

Transducer description, page 25

Installation trunk description, page 26

Display description

A display is a required part of the MF90 system. For best readability, the display must be
protected from glare and have the correct height and angle.

Any commercial display can be used with the MF90 system, provided that the chosen
display meets the minimum requirements.

Tip

You may find it useful to have more than one display connected to the MF90 system. The
number of displays must be chosen to fit the preferences of the crew.

The display is not a standard part of the delivery. This is a commercial item that can
be purchased locally. Kongsberg Maritime may provide a suitable display. The chosen
display must be designed for maritime use, and it must meet the minimum performance
specifications. The video interface must match the output format(s) provided by the
Processor Unit.

Related topics

Simrad MF90, page 13
System units, page 20
Installing the MF90 system hardware units, page 126
Cable layout and interconnections, page 143
Setting to work, page 186
Technical specifications, page 346
Drawing file, page 364

Simrad MF90 Installation Manual

Summary of Contents for Simrad MF90











































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands