Kongsberg Simrad MF90 Page 148 Installation Manual Download | Manualshive

Page: 148 / 426

background image

146

476671/B

Topside cable plan

The topside/bridge cables include those used to connect the Processor Unit and the display
to each other, as well as cables for AC mains power and external devices. The connection
between the Processor Unit and the operating panel is also shown.

A

Uninterruptible power supply (UPS)

B

Processor Unit

C

Display

D

Operating Panel (Mk2)

E

Operating Panel (Mk3)

F

Power Supply Unit

Cables identified with an asterisk (*) are system or commercial cables. These cables are
provided in the delivery or with the relevant item. Cable numbers that are not used are
spares for optional equipment and/or future expansions.

The HT20470 Processor Unit is available in two versions. The DC version operates on +24
VDC while the AC version operates on 100 to 240 VAC. A power supply is required if a DC
powered unit needs to work from an AC supply. The power supply offers a 24 VDC output.

The MF90 system supports two different operating panels.

For more information about the cables, see:

Comments

.

Simrad MF90 Installation Manual

«
...
146
147
148
149
150
...
»

Summary of Contents for Simrad MF90











































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Simrad MF90

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands