Kongsberg Simrad MF90 Page 60 Installation Manual Download | Manualshive

Page: 60 / 426

background image

58

476671/B

Cable

Description

Length

C1

This is a commercial cable. The power cable is provided with the
uninterrupted power supply (UPS) unit.

(*)

C2

This is a commercial cable. The power cable is provided with
the display.

(*)

C3

Power cable

(*)

C4

This cable must be provided by the installation shipyard. This
cable is only required if the DC version of the Processor Unit
needs to operate from AC power.

C5

Power cable. This cable is only used with Operating Panel Mk2.

(*)

C6

This cable must be provided by the installation shipyard.

C7

This cable must be provided by the installation shipyard.

Ethernet cable

100

C8

It is very important that high-quality Ethernet cables are used. Do not make the
connection using the existing local area network (LAN).

C9

This is a commercial cable.

C10

This cable must be provided by the installation shipyard.

C11

This is a commercial cable. This cable is only used with
Operating Panel Mk3.

3

C12

A dedicated Ethernet cable is used to connect the Operating Panel
to the Processor Unit. This is a commercial cable. This cable is
only used with Operating Panel Mk2.

5

C13

These cables must be provided by the installation shipyard.

C14

These cables must be provided by the installation shipyard.

C15

This cable must be provided by the installation shipyard.

(*) Commercial power cables are provided with different lengths. The typical length of a power cable is
between 1.5 and 2.5 metres. If the power cable provided is too short you must use an extension cable (not
recommended), mount a new power outlet within range, or make your own power cable with sufficient
length.

Related topics

Preparations, page 42
Location of hardware units on the bridge, page 56
Installing the MF90 system hardware units, page 126
Drawing file, page 364

Simrad MF90 Installation Manual

«
...
58
59
60
61
62
...
»

Summary of Contents for Simrad MF90











































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Simrad MF90

Brand: Hummingbird Communications Pages: 36

Brand: Humminbird Pages: 2

Brand: Garmin Pages: 50

echo 200 Series

Brand: Garmin Pages: 28

Brand: Navman Pages: 30

Brand: Garmin Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands