Kongsberg Simrad MF90 Installation Manual Download | Manualshive

Page: 146 / 426

background image

144

476671/B

Read this first

Detailed information about cable specifications, termination and connectors is provided.
Unless otherwise specified, all cables are supplied by Kongsberg Maritime as a part of the
delivery.

Detailed information about relevant cable specifications, termination and connectors is
provided. Each drawing provides additional information, and may, when applicable, include
minimum specifications, connector terminations and the required number of cores. Drawings
are generally not provided for standard commercial cables. Cables fall into three categories.

System cables

System cables are provided by Kongsberg Maritime as a part of the delivery.

Shipyard cables

Shipyard cables must be provided by the shipyard doing the installation, or the
shipowner. The cables must meet the minimum specifications provided in this
publication.

Commercial cables

Commercial cables may be provided by Kongsberg Maritime as a part of the delivery.
The cables may also be included with third party items that are used with the MF90
system.

All electric installations and corresponding wiring must be in accordance with the vessel's
national registry and corresponding maritime authority and/or classification society.

Note

It is very important that all cables are properly installed and correctly terminated. Observe
the relevant regulations and work standards. Always leave enough cable slack close to
system units and cabinets to allow for maintenance.

Only skilled and authorized personnel can install the MF90 cables.

Kongsberg Maritime accepts no responsibility for damage to the system, or reduced
operational performance, when this is caused by improper wiring.

Before you install or maintain the system cables, make sure that the AC mains circuit
breaker for the system is disconnected.

Related topics

Cable layout and interconnections, page 143
Cable plans, page 145
Installing the MF90 cables, page 154
Cable drawings and specifications, page 164

Simrad MF90 Installation Manual

«
...
144
145
146
147
148
...
»

Summary of Contents for Simrad MF90











































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Simrad MF90

Brand: FLIR Pages: 136

Brand: Standard Horizon Pages: 168

Brand: Eagle Pages: 24

Brand: Eagle Pages: 26

Brand: Garmin Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands