Kongsberg Simrad MF90 Installation Manual Download | Manualshive

Page: 357 / 426

background image

476671/B

355

Weights and outline dimensions

These weights and outline dimension characteristics summarize the physical properties of
the MF90 system.

Topics

Display weight and outline dimensions, page 355

Operating Panel weight and outline dimensions (Mk2), page 355

Operating Panel weight and outline dimensions (Mk3), page 356

Transceiver Unit weight and outline dimensions, page 356

Hull Unit weight and outline dimensions, page 356

Display weight and outline dimensions

Not applicable. The display is not a part of the MF90 scope of supply. It is not manufactured
by Kongsberg Maritime. For more information, refer to the end-user documentation
provided by the manufacturer.

Related topics

Technical specifications, page 346
Weights and outline dimensions, page 355

Operating Panel weight and outline dimensions (Mk2)

•

Make and model

: MF90 Operating Panel (Mk2)

•

Outline dimensions

:

–

Depth

: 183 mm

–

Width

: 346 mm

–

Height

: 123 mm

•

Weight

: 3.7 kg (Approximately)

Related topics

Technical specifications, page 346
Weights and outline dimensions, page 355

Technical specifications

«
...
355
356
357
358
359
...
»

Summary of Contents for Simrad MF90











































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Simrad MF90

GWS 10 Marine Wind Sensor

Brand: Garmin Pages: 48

Brand: NorthStar Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands