manualshive.com logo in svg

KEB COMBIVERT F4-F, Applications Manual, Page: 228 / 300

Share
Download
KEB COMBIVERT F4-F Applications Manual Download Page 228

6

11

KEB COMBIVERT F4-F

18

Name: Basis

17.06.99

Chapter

Section

Page

Date

©

KEB Antriebstechnik, 1999
All Rights reserved

Functional Description

Positioning Module

6.11.19 Programming

Examples

Positioning control

with four positions

Requirements:

• four different positions shall be approached by the control
• the addressing of the positions is done by way of erminal strip
• the positioning starts with ‘start positioning’ - signal
• output D1 shall be set when the target is reached
• after power-on the reference point approach shall be started with ‘start

positioning’

• the positions are adjusted absolute referring to the reference point

(adjustment in increments, position setpoint values = 80500,  1286000,
24000, 163800)

• the absolute positions - 320000 and +1500000 are the limit for the

position setpoint value

• the positions are indicated and adjusted in decimal values
• when a digital input is set it shall be possible to handle the drive manually

with the analog setpoint value (emergency operation)

• the left limit switch is also the reference switch with turning back to zero

position

Sequence:

• the control selects the positioning set
• after that the control gives ‘start positioning’

(positioning set must still be present at the terminal strip)

• the controller takes the position, speed and controller setting etc. from the

selected positioning set

• after reaching the target window and termination of precontrol signal the

‘target window reached‘ signal is set

• only now new set addresses and a new ‘start positioning’ -command

are accepted

• the signal ‘target window reached’ is reset with the new ‘start

positioning’ -command

• if I4 is activated the controller operates with the analog setpoint value

Positioning - control (Pc) - Parameter

Pc. 0

Positioning module

1

on

Pc. 1

Adjustment mode

0

position display / -setting in increments

Pc. 4

Limit position left sign

-1

negative position value for limit position left

Pc. 5

Limit position left high

32

limit position left high * 10000 = 320.000 increments

Pc. 6

Limit position left low

0

limit position left low = 0 increments

Pc. 7

Limit position right sign

0

positive position value for limit position right

Pc. 8

Limit position right high

150

limit position right high * 10000 = 1.500.000 increments

Pc. 9

Limit position right low

0

limit position right low = 0 increments

Pc.10 Reference point mode

1

auto ref on

Pc.11 Reference point sign

0

Pc.12 Reference point high

0

reference point position = zero point

Pc.13 Reference point low

0

Pc.14 Reference speed

-100

the reference point is searched for with a speed of 100 rpm in rotation

direction left / automatic reversal of rotation direction on reaching the limit

switch / negative speed, since the reference point lies on the left limit

switch

Summary of Contents for COMBIVERT F4-F













































































































































































































































































































Reviews:

No comments