manualshive.com logo in svg

KEB COMBIVERT F4-F, Applications Manual, Page: 201 / 300

Share
Download
KEB COMBIVERT F4-F Applications Manual Download Page 201

9

ANTRIEBSTECHNIK

6

9

9

KEB COMBIVERT F4-F

Name: Basis

09.08.00

6

Section

Page

Date

©

KEB Antriebstechnik, 1999
All Rights reserved

Chapter

Functional Desription

Encoder Interface

6.9.5

Basic Setting

Prior to start-up the inverter must be adapted to the encoder(s) which is/are used.

Adjustment of encoder line

number

(dr.25, dr.30)

Cable length

To achieve an unobjectionable function following cable lengths should not be exceeded.
Precondition for it is that the supply voltage at the rotary encoder is within the specified
tolerances.

The encoder lines should not be longer than 50 m. If longer cables are needed,
please contact KEB.

Further information can be taken from the documentation of the respective
manufacturer.

With this parameter the encoder line number is adjusted to the connected encoder
within a range of 256…10000.

• dr.25 for encoder interface  1
• dr.30 for encoder interface  2

Encoder track change

(dr.29, dr.34)

If you find that during start-up in controlled operation the actual and setpoint speed
have different signs it can be an indication for a wrong connection of the incremental
encoder. If possible the wiring should be corrected. Should this involve too much
effort then you can achieve a rotation reversal of encoder 1 by means of dr.29. The
effect corresponds to a change of the A and B tracks of the incremental encoder.
With parameter dr.34 it is possible to achieve a track change of encoder 2.

This parameter defines the time over which the speed average is determined. At that
the resolution of the speed detection is defined simultaneously.

dr.40 Sampling

Speed resolution with the use of an

time

incremental encoder with 2500 pulses

0

0,5 ms

12 min

-1

1

1 ms

6 min

-1

2

2 ms

3 min

-1

3

4 ms

1,5 min

-1

(factory setting)

4

8 ms

0,75 min

-1

5

16 ms

0,375 min

-1

Speed sampling time

(dr.40)

When using other line numbers:

Speed resolution =

Specified speed resolution x 2500

Line number

Encoder resolution

(dr.28)

When connecting sine / cosine encoders the accuracy of the position recording is
improved by activating the high-resolution (dr.28 = 1). For incremental encoders with
rectangular signals the adjustment must be dr.28 = 0.

Summary of Contents for COMBIVERT F4-F













































































































































































































































































































Reviews:

No comments