manualshive.com logo in svg

Intel NIOS II, Owner Reference Manual

Share
Download
Intel NIOS II Owner Reference Manual Download Page 85

For information about controlling this option, refer to the Instantiating the Nios II

Processor chapter of the Nios II Processor Reference Handbook.

When the processor issues an instruction with an undefined opcode or opcode-

extension field, and illegal instruction exception checking is turned on, an illegal

instruction exception is generated.

Refer to the OP Encodings and OPX Encodings for R-Type Instructions tables in the

Instruction Set Reference chapter of the Nios II Processor Reference Handbook to see

the unused opcodes and opcode extensions.

Note: 

All undefined opcodes are reserved. The processor does occasionally use some

undefined encodings internally. Executing one of these undefined opcodes does not

trigger an illegal instruction exception.

Refer to the Nios II Core Implementation Details chapter of the Nios II Processor

Reference Handbook for information about each specific Nios II core.

Related Information

•

Instruction Set Reference

 on page 169

•

Programming Model

 on page 36

•

Nios II Core Implementation Details

 on page 121

3.7.7.5. Supervisor-Only Instruction

When your system contains an MMU or MPU and the processor is in user mode
(

status.U = 1

), executing a supervisor-only instruction results in a supervisor-only

instruction exception. The supervisor-only instructions are 

initd

, 

initi

, 

eret

,

bret

, 

rdctl

, and 

wrctl

.

This exception is implemented only in Nios II processors configured to use supervisor

mode and user mode. Refer to the "Operating Modes" section of this chapter for more

information.

Related Information
Operating Modes

 on page 36

3.7.7.6. Supervisor-Only Instruction Address

When your system contains an MMU and the processor is in user mode (

status.U =

1

), attempts to access a supervisor-only instruction address result in a supervisor-only

instruction address exception. Any instruction fetch can cause this exception. For

definitions of supervisor-only address ranges, refer to the Virtual Memory Partitions

Table.

This exception is implemented only in Nios II processors that include the MMU.

Related Information
Virtual Memory Address Space

 on page 39

3. Programming Model

NII-PRG | 2018.04.18

Nios II Processor Reference Guide

85

Summary of Contents for NIOS II










































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands