Intel NIOS II Owner Reference Manual Download

Page: 58 / 233

Table 26.

badaddr Control Register Fields

Bit Fields

BADDR

Table 27.

badaddr Control Register Field Descriptions

Field

Description

Access

Reset

Availabl

BADDR

contains the byte instruction address or data address

associated with an exception when certain exceptions occur. The

Address column of the Nios II Exceptions Table lists which exceptions
write the

BADDR

field.

Read

Only

with

Nios II/f

The

BADDR

field allows up to a 32-bit instruction address or data address. If an MMU

or MPU is present, the

BADDR

field is 32 bits because MMU and MPU instruction and

data addresses are always full 32-bit values. When an MMU is present, the

BADDR

field

contains the virtual address.

If there is no MMU or MPU and the Nios II address space is less than 32 bits, unused

high-order bits are written and read as zero. If there is no MMU, bit 31 of a data
address (used to bypass the data cache) is always zero in the

BADDR

field.

Related Information

•

Exception Overview

on page 75

•

Programming Model

on page 36

3.4.2.12. The config Register

The

config

preserved during exception processing (in contrast to the information in the

status

Table 28.

config Control Register Fields

Bit Fields

Reserved

ECCE

ANI

3. Programming Model

NII-PRG | 2018.04.18

Nios II Processor Reference Guide

Summary of Contents for NIOS II










































































































































































































































Search results

Summary of Contents for NIOS II

Reviews:

Related manuals for NIOS II

Brands by name

Popular brands

Intel NIOS II, Owner Reference Manual

Search results

Summary of Contents for NIOS II

Reviews:

Related manuals for NIOS II

Brands by name

Popular brands