Intel NIOS II Owner Reference Manual Download

Page: 64 / 233

3.4.2.14.6. The WR Flag

Setting the

flag signifies that an MPU region write operation should be performed

when a

wrctl

instruction is issued to the

mpuacc

Read and Write Operations section for more information. The

flag always returns 0

when read by a

rdctl

instruction.

Note:

Setting both the

and

flags to one results in undefined behavior.

Related Information
MPU Region Read and Write Operations

on page 68

3.4.2.14.7. The eccinj Register

The

eccinj

blocks that support ECC. Injecting errors allows the software to test the ECC error

exception handling code. The error(s) are injected in the data bits, not the parity bits.
The

eccinj

Table 38.

eccinj Control Register Fields

Bit Fields

Reserved

DC WB

DTCM 3

DTCM 2

DTCM 1

DTCM 0

TLB

DC DAT

DC TAG

ICDAT

ICTAG

Software writes 0x1 to inject a 1 bit ECC error or 0x2 to inject a 2-bit ECC error to the

RAM field. Hardware sets the value of the inject field to 0x0 after the error injection

has occurred.

Table 39.

eccinj Control Register Field Descriptions

Field

Description

Access

Reset

Availabl

Inject an ECC error in the register file’s RAM.

Read/Write

Only

with

ECC

ICTAG

Inject an ECC error in the instruction cache Tag RAM.

Read/Write

Only

with

ECC

ICDAT

Inject an ECC error in the instruction cache data RAM.

Read/Write

Only

with

ECC

DCTAG

Inject ECC error in data cache tag RAM.

Read/Write

DCDAT

Inject an ECC error in the data cache data RAM. Injection occurs on

next store instruction that writes the data cache or the next line fill.

Read/Write

TLB

Inject an ECC error in the MMU TLB RAM. Errors are injected in the tag

portion of the VPN field.

Read/Write

Only

with

ECC

DTCM0

Inject ECC error in DTCM0. Injection occurs on next store instruction

that writes this DTCM.

Read/Write

continued...

3. Programming Model

NII-PRG | 2018.04.18

Nios II Processor Reference Guide

Summary of Contents for NIOS II










































































































































































































































Search results

Summary of Contents for NIOS II

Reviews:

Related manuals for NIOS II

Brands by name

Popular brands

Intel NIOS II, Owner Reference Manual

Search results

Summary of Contents for NIOS II

Reviews:

Related manuals for NIOS II

Brands by name

Popular brands