HP StorageWorks SN6000 Command Line Interface Manual Download Page 175

Page: 175 / 330

HP StorageWorks SN6000 Fibre Channel Switch Command Line Interface Guide 175

profile

Description

Creates and modifies profiles with which to customize Call Home email notification. A profile defines

the event severity level at which to generate emails, email subject and text, and email recipients.

NOTE:

The Call Home service provides an email notification capability for the switch. This service

has no relationship with the HP Call Home feature, which notifies HP services.

Authority

Admin session and a Callhome Edit session. For information about starting a Callhome Edit session,

see the

callhome

command.

Syntax

profile

copy [profile_source] [profile_destination]

create [profile]

delete [profile]

edit [profile]

rename [profile_old] [profile_new]

Operands

copy [profile_source] [profile_destination]

Creates a new profile named [profile_destination] and copies the configuration into it from the

profile given by [profile_source]. You must enter the

callhome save

command to save your

changes. Neither [profile_source] nor [profile_destination] can be Tech_Support_Center.

create [profile]

Creates a profile with the name given by [profile]. A profile name must begin with a letter and be

no longer than 32 characters. Valid characters are alphanumeric, _, $, ^, and -. The

Tech_Support_Center profile name is reserved. The Call Home database supports a maximum of

25 profiles. You must enter the

callhome save

command to save your changes.

Table 15

describes the profile configuration parameters.

Table 15

Profile configuration parameters

Parameter

Description

Level

Event severity level at which to generate a Call Home email message:

•

None

—Generates email messages for all events.

•

Warn

—Generates email messages for Warning, Critical, and Alarm

events.

•

Critical

—Generates email messages for Critical and Alarm events.

•

Alarm

—Generates email messages for Alarm events only.

Format

Level of detail to be included in the email message:

•

ShortText

—Includes switch and event information.

•

FullText

—Includes switch information, event information, Call Home

contact information, and SNMP contact information.

•

Tsc1—Includes switch and event information in a format intended for

automated email readers.

MaxSize

Maximum number of characters allowed in the email message. Decreasing

this parameter makes it easier to read messages on small display devices

such as cell phones. The minimum is 650. The maximum and default is

2,000,000.

EmailSubject

Subject of the email; up to 64 characters

Summary of Contents for StorageWorks SN6000











































































































































































































































































































































Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands

HP StorageWorks SN6000, Command Line Interface Manual

Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands