HP StorageWorks SN6000 Command Line Interface Manual Download Page 47

Page: 47 / 330

HP StorageWorks SN6000 Fibre Channel Switch Command Line Interface Guide

The restore process replaces all configuration information on the switch and afterwards the switch is

automatically reset. If the restore process changes the IP address, all management sessions are terminated.

Use the

set setup system

command to return the IP configuration to the values you want. To restore

the switch, open a Telnet session (a new IP address may be required), then enter the

config restore

command from in an Admin session, as shown in the following example:

SN6000 FC Switch #> admin start

SN6000 FC Switch (admin) #> config restore

The switch will be reset after restoring the configuration.

Please confirm (y/n): [n] y

Alarm Msg: [day month date time year][A1005.0021][SM][Configuration is being
restored - this could take several minutes]

Alarm Msg: [day month date time year][A1000.000A][SM][The switch will be reset
in 3 seconds due to a config restore]

SN6000 FC Switch (admin) #>

Alarm Msg: [day month date time year][A1000.0005][SM][The switch is being reset]

Paging a switch

To help you locate a particular switch in a rack of switches, you can turn on the beacon feature with the

set beacon

command. This causes all port Logged-In LEDs to flash in unison. The following is an

example of how to turn the beacon on and off:

SN6000 FC Switch #> set beacon on

SN6000 FC Switch $> set beacon off

Managing the date and time

The switch date and time can be set explicitly using the

date

command or it can be set automatically

through a Network Time Protocol (NTP) server. The

date

command also displays the current time. Unlike

the

date

command, the NTP server also synchronizes the date and time on the switch with the date and

time on the workstation, which is required for SSL connections.

NOTE:

To set the date with the

date

command, the switch NTP client must be disabled. For information

about disabling the

NTPClientEnabled

parameter, see ”

set setup system

” (page 222).

If you are using the

date

command, you can set the time zone using the

set timezone

command. The

default time zone is Universal Time (UTC) also known as Greenwich Mean Time (GMT). Changing the time

zone converts the current time to the time in the new time zone. For this reason, if you are not using an NTP

server, set the time zone first, then set the date and time.
See the following date and time management examples:

•

Displaying the date and time

, page 47

•

Setting the date and time explicitly

, page 48

•

Setting the time through an NTP server

, page 49

Displaying the date and time

To display the date and time, enter the

date

command, as shown in the following example:

SN6000 FC Switch #> date

Mon Apr 07 07:51:24 2008

Summary of Contents for StorageWorks SN6000











































































































































































































































































































































Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands

HP StorageWorks SN6000, Command Line Interface Manual

Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands