HP StorageWorks SN6000 Command Line Interface Manual Download Page 26

Page: 26 / 330

Network Configuration

IMPORTANT:

IP security configurations can be complex: it is possible to unintentionally configure policies

and associations that isolate a switch from all communication. If this happens, you can disable IP security

by placing the switch in maintenance mode, and correct the problem through the serial port interface. For

information about using maintenance mode and connecting through the serial port, see the

StorageWorks SN6000 Fibre Channel Switch Installation and Reference Guide

Displaying IP security information

You can display the security policy and security association databases sorted by the following parameters:

•

Active policies and associations; that is, policies and associations currently in use

•

Configured policies and associations; that is, policies and associations that have been saved in the

database

•

Policies and associations that are being edited, but have not been saved

You can display the following types of IP security configuration information:

•

Policy and association information

, page 26

•

IP security configuration history

, page 27

•

IP security configuration limits

, page 27

Policy and association information

To display general or specific policy and association information, enter the

ipsec list

command. The

ipsec list

command does not require an Admin session or an Ipsec Edit session. However, in an Ipsec

Edit session, the

ipsec association list

and

ipsec policy list

commands display the same

information.
The following example displays all active policies and associations:

SN6000 FC Switch #> ipsec list

Active IPsec Information

Security Association Database

-----------------------------

h2h-sh-sa

h2h-hs-sa

Security Policy Database

------------------------

h2h-hs-sp

h2h-sh-sp

Summary

-------

Security Association Count: 2

Security Policy Count: 2

Summary of Contents for StorageWorks SN6000











































































































































































































































































































































Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands

HP StorageWorks SN6000, Command Line Interface Manual

Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands