HP StorageWorks SN6000 Command Line Interface Manual Download Page 146 | Manualshive

Page: 146 / 330

background image

146 Command Reference

firmware install

Description

Downloads firmware from a remote host to the switch, installs the firmware, then resets the switch to

activate the firmware. This is disruptive. The command prompts you for the following:

•

The file transfer protocol (FTP or TFTP)

•

IP address or DNS host name of the remote host

•

An account name and password on the remote host (FTP only)

•

Pathname for the firmware image file

Authority

Admin session

Syntax

firmware install

Examples

The following is an example of the

firmware install

command using FTP:

SN6000 FC Switch #> admin start

SN6000 FC Switch (admin) #> firmware install

The switch will be reset. This process will cause a disruption
to I/O traffic.

Continuing with this action will terminate all management sessions,
including any Telnet sessions. When the firmware activation is complete,
you may log in to the switch again.

Do you want to continue? [y/n]: y

Press 'q' and the ENTER key to abort this command.

FTP or TFTP : ftp

User Account : johndoe

IP Address : 10.0.0.254

Source Filename : 8.0.00.xx_epc

About to install image. Do you want to continue? [y/n] y

Connected to 10.0.0.254 (10.0.0.254).

220 localhost.localdomain FTP server (Version wu-2.6.1-18) ready.

331 Password required for johndoe.

Password: xxxxxxxxx

230 User johndoe logged in.

bin

200 Type set to I.

verbose

Verbose mode off.

This may take several seconds...

The switch will now reset.

Connection closed by foreign host.

«
...
144
145
146
147
148
...
»

Summary of Contents for StorageWorks SN6000











































































































































































































































































































































Reviews:

No comments

Related manuals for StorageWorks SN6000

Brand: Mackie Pages: 4

Brand: EBECO Pages: 8

Brand: TDK-Lambda Pages: 20

7512 440V 16A CL1

Brand: Ivela Pages: 2

Brand: Van Essen Pages: 16

Brand: Bachmann Pages: 2

Brand: Cameo Pages: 164

Brand: Lindy Pages: 8

Brand: Lindy Pages: 2

Brand: Lindy Pages: 12

NEXTGEN USB CABLE

Brand: Digifly Pages: 2

Brand: Rutenbeck Pages: 6

Brand: Lindy Pages: 9

Brand: enphase Pages: 28

Brand: marklin Pages: 12

Brand: HDCVT TECHNOLOGY Pages: 5

Brand: HDCVT TECHNOLOGY Pages: 7

FuseConnect-MPO

Brand: Fujikura Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands