HP StorageWorks SN6000 Command Line Interface Manual Download Page 43

Page: 43 / 330

HP StorageWorks SN6000 Fibre Channel Switch Command Line Interface Guide

To configure the switch services, enter the

set setup services

command in an Admin session, as

shown in the following example:

SN6000 FC Switch #> admin start

SN6000 FC Switch (admin) #> set setup services

A list of attributes with formatting and current values will follow.

Enter a new value or simply press the ENTER key to accept the current value.

If you wish to terminate this process before reaching the end of the list

press 'q' or 'Q' and the ENTER key to do so.

PLEASE NOTE:

-----------

* Further configuration may be required after enabling a service.

* If services are disabled, the connection to the switch may be lost.

* When enabling SSL, please verify that the date/time settings

on this switch and the workstation from where the SSL connection

will be started match, and then a new certificate may need to be

created to ensure a secure connection to this switch.

TelnetEnabled (True / False) [True ]

SSHEnabled (True / False) [False]

GUIMgmtEnabled (True / False) [True ]

SSLEnabled (True / False) [False]

EmbeddedGUIEnabled (True / False) [True ]

SNMPEnabled (True / False) [True ]

NTPEnabled (True / False) [False]

CIMEnabled (True / False) [False]

FTPEnabled (True / False) [True ]

MgmtServerEnabled (True / False) [True ]

CallHomeEnabled (True / False) [True ]

Do you want to save and activate this services setup? (y/n): [n]

Summary of Contents for StorageWorks SN6000











































































































































































































































































































































Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands

HP StorageWorks SN6000, Command Line Interface Manual

Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands