HP StorageWorks SN6000 Command Line Interface Manual Download Page 261

Page: 261 / 330

HP StorageWorks SN6000 Fibre Channel Switch Command Line Interface Guide 261

show port

Description

Displays operational information for one or more ports.

Authority

None

Syntax

show port

Table 64

describes the information returned by the

show port

command.

Table 64

Show port display entries

Parameter

Description

AdminState

Administrative state

AIinit

Number of times the port begins arbitrated loop initialization

AIinitError

Number of times the port entered initialization and the initialization

failed

AsicNumber

Application-specific integrated circuit (ASIC) number

AsicPort

ASIC port number

BadFrames

Number of frames that have framing errors.

BBCR_FrameFailures

Number of times more frames were lost during a credit recovery period

than the recovery process could resolve. This causes a Link Reset to

recover the credits.

BBCR_RRDYFailures

Number of times more Receiver_Ready (R_RDY) primitives were lost

during a credit recovery period than the recovery process could resolve.

This causes a Link Reset to recover the credits.

ClassXFramesIn

Number of class

frames received by this port

ClassXFramesOut

Number of class

frames sent by this port

ClassXWordsIn

Number of class

words received by this port

ClassXWordsOut

Number of class

words sent by this port

ClassXToss

Number of times an SOFi3 or SOFn3 frame is tossed

ConfigType

Configured port type:

, or

Donor

DecodeError

Number of decode errors detected

POSTFaultCode

Fault code from the most recent power-on self test

POSTStatus

Status from the most recent power-on self test

DownstreamISL

Downstream ISL state.

True

indicates a connection to another switch

that is not the principal switch.

EpConnects

Number of times an E_Port connected through ISL negotiation

EpConnState

E_Port connection status

EpIsoReason

E_Port isolation reason

FBusy

Number of times the switch sent a fabric busy (F_BSY) frame because

the Class 2 frame could not be delivered within ED_TOV time; or the

number of class 2 and class 3 F_BSY frames generated by this port in

response to incoming frames. This usually indicates a busy condition on

the fabric or N_Port that is preventing delivery of this frame.

Summary of Contents for StorageWorks SN6000











































































































































































































































































































































Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands

HP StorageWorks SN6000, Command Line Interface Manual

Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands