HP StorageWorks SN6000 Command Line Interface Manual Download | Manualshive

Page: 181 / 330

background image

HP StorageWorks SN6000 Fibre Channel Switch Command Line Interface Guide 181

switch

Resets the switch without a power-on self test (POST). This is the default. This reset disrupts traffic

and does the following:
• Activates the pending firmware
• Closes all management sessions
• Clears the event log. To save the event log before resetting, see the ”

set log

” (page 206).

To reset the switch with a power-on self test, see the ”

hardreset

” (page 154). To reset the switch

without disrupting traffic, see the ”

hotreset

” (page 157).

NOTE:

The following files are deleted from the switch during a switch reset:

• Firmware image files that have not been unpacked
• Configuration backup files
• Support files

system

Resets the following system configuration settings to the factory default values:
• DNS host (

Table 24

)

• IPv4 Ethernet (

Table 25

)

• IPv6 Ethernet (

Table 26

)

• Event logging (

Table 27

)

• NTP (

Table 28

)

• Timers (

Table 29

)

NOTE:

Because this operand changes network parameters, the workstation could lose

communication with the switch. This operand does not affect installed license keys.

zoning

Clears the zoning database and deactivates the active zone set. The zoning configuration

parameters (

MergeAutoSave

,

DefaultZone

,

DiscardInactive

) remain unchanged. See

Table 20

for information about the zoning configuration parameters.

«
...
179
180
181
182
183
...
»

Summary of Contents for StorageWorks SN6000











































































































































































































































































































































Reviews:

No comments

Related manuals for StorageWorks SN6000

Brand: Hailink Pages: 6

Brand: ScatterBox Pages: 2

Brand: YOKOGAWA Pages: 2

EGE-UHD-2HDB-1431L

Brand: geratech Pages: 14

Brand: Tripp Lite Pages: 2

PYROLINE Con BSK

Brand: OBO Bettermann Pages: 62

Brand: DH Instruments Pages: 20

Brand: OBO Bettermann Pages: 2

Brand: Staubli Pages: 12

Brand: Staubli Pages: 16

Brand: Staubli Pages: 16

CombiTac direqt

Brand: Staubli Pages: 24

CAN-T-Connector

Brand: ESD Pages: 22

Brand: Novus Pages: 12

DEVIpipeheat 10 V3

Brand: Danfoss Pages: 88

Brand: Yellobrik Pages: 17

Optimus DB Reducers

Brand: nestor cables Pages: 6

Brand: nestor cables Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands