HP StorageWorks SN6000 Command Line Interface Manual Download Page 254

Page: 254 / 330

254 Command Reference

Table 62

Transceiver information

Entry

Description

MediaType

Media physical variant. The variant indicates speed, media,

transmitter, and distance. The media designator may be M5

(multimode 50 micron), M6 (multimode 62.5 micron), or MX.

MX indicates that the media supports both multimode 50 and

62.5 micron.

MediaType

may also be one of the following:

•

NotInstalled–transceiver is not installed.

•

Unknown–transceiver does not have a serial ID.

•

NotApplicable–transceiver is not needed.

MediaVendor

Vendor name

MediaPartNumber

Vendor media part number

MediaRevision

Vendor media revision level

MediaSerialNumber

Vendor media serial number

MediaSpeeds

Transmission speed capabilities

Temp

Temperature in degrees Celsius

Voltage

Supply voltage in Volts. The range is 0–6.55.

Tx Bias

Transmitter laser bias current in milliamps. The range is 0–655.

Tx Power

Transmitter coupled output power in milliWatts. The range is

0–6.55.

Rx Power

Received optical power in milliWatts. The range is 0–6.55.

Value

Measured value

Status

State associated with the measured value:

•

Normal: Value is in the normal operating range.

•

HighAlarm: Value exceeds the high alarm threshold.

•

HighWarning: Value exceeds the high warning threshold.

•

LowWarning: Value is less than the low warning threshold.

•

LowAlarm: Value is less than the low alarm threshold.

HighAlarm

Vendor specified threshold above which an alarm is issued

HighWarning

Vendor specified threshold above which a warning is issued

LowWarning

Vendor specified threshold below which a warning is issued

LowAlarm

Vendor specified threshold below which an alarm is issued

Summary of Contents for StorageWorks SN6000











































































































































































































































































































































Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands

HP StorageWorks SN6000, Command Line Interface Manual

Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands