HP StorageWorks SN6000 Command Line Interface Manual Download Page 168

Page: 168 / 330

168 Command Reference

ipsec policy

Description

Manages policies in the Security Policy database.

Authority

Admin session and an Ipsec Edit session

Syntax

ipsec policy

copy [policy_source] [policy_destination]

create [policy]

delete [policy]

edit [policy]

list

[option]

rename [policy_old] [policy_new]

Operands

copy [policy_source] [policy_destination]

Creates a new policy named [policy_destination] and copies the configuration into it from the

policy given by [policy_source]. You must enter the

ipsec save

command afterwards to save

your changes. [policy_destination] must not begin with

DynamicSP_

, which is reserved for

dynamic policies.

create [policy]

Creates a policy with the name given by [policy]. A policy name must begin with a letter and be

no longer than 32 characters. Valid characters are alphanumeric, _, $, ^, and -. The Security

Policy database supports a maximum of 128 user-defined policies. You must enter the

ipsec save

command afterwards to save your changes.

Table 14

describes the policy

parameters:

Table 14

Policy configuration parameters

Parameter

Description

Description

Description of the policy

SourceAddress

IP address (version 4 or 6) or DNS host name of the host, switch, or

gateway from which data originates

SourcePort

Source port number in the range

—

65535

DestinationAddress

IP address (version 4 or 6) or DNS host name of the host, switch, or

gateway receiving data. If you specified an IP address for the

SourceAddress

, the

DestinationAddress

must use the same

IP version format.

DestinationPort

Destination port number in the range

—

65535

Protocol

Protocol or application to which to apply IP security. Enter an

operand for one of the following protocols or an integer in the

range

—

255

•

Internet Control Message Protocol for IPv4 (ICMP)

•

Internet Control Message Protocol for IPv6 (ICMP6)

•

Internet Protocol, version 4 (IPv4)

•

Transmission Control Protocol (TCP)

•

User Datagram Protocol (UDP)

•

Any protocol

ICMPv6 Type

ICMP number (0–255). You are prompted for this parameter only if

you specify ICMP6 for the Protocol parameter.

Summary of Contents for StorageWorks SN6000











































































































































































































































































































































Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands

HP StorageWorks SN6000, Command Line Interface Manual

Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands