HP StorageWorks SN6000 Command Line Interface Manual Download Page 303

Page: 303 / 330

HP StorageWorks SN6000 Fibre Channel Switch Command Line Interface Guide 303

zoneset

Description

Manages zone sets and component zones across the fabric.

Authority

Admin session and a Zoning Edit session. See the

zoning edit

command. The

active

list

and

zones

operands are available without an Admin session. You must close the Zoning Edit

session before using the

activate

and

deactivate

operand.

Syntax

zoneset

activate [zone_set]

active

add [zone_set] [zone_list]

copy [zone_set_source] [zone_set_destination]

create [zone_set]

deactivate

delete [zone_set]

list

remove [zone_set] [zone_list]

rename [zone_set_old] [zone_set_new]

zones [zone_set]

Operands

activate [zone_set]

Activates the zone set given by [zone_set]. This operand deactivates the active zone set. Close

the Zoning Edit session before using this operand.

active

Displays the name of the active zone set. This operand does not require Admin session.

add [zone_set] [zone_list]

Adds a list of zones and aliases given by [zone_list] to the zone set given by [zone_set]. Use a

<space> to delimit zone and alias names in [zone_list]. You must enter the

zoning save

command to save your changes.

copy [zone_set_source] [zone_set_destination]

Creates a new zone set named [zone_set_destination] and copies into it the zones from the zone

set given by [zone_set_source]. You must enter the

zoning save

command to save your

changes.

create [zone_set]

Creates the zone set with the name given by [zone_set]. A zone set name must begin with a letter

and be no longer than 64 characters. Valid characters are alphanumeric, _, $, ^, and -. The

zoning database supports a maximum of 256 zone sets. You must enter the

zoning save

command to save your changes.

deactivate

Deactivates the active zone set. Close the Zoning Edit session before using this operand.

delete [zone_set]

Deletes the zone set given by [zone_set]. If the specified zone set is active, the command is

suspended until the zone set is deactivated. You must enter the

zoning save

command to save

your changes.

list

Displays a list of all zone sets. This operand does not require an Admin session.

remove [zone_set] [zone_list]

Removes a list of zones given by [zone_list] from the zone set given by [zone_set]. Use a

<space>

to delimit zone names in [zone_list]. If [zone_set] is the active zone set, the zone will

not be removed until the zone set has been deactivated. You must enter the

zoning save

command to save your changes.

Summary of Contents for StorageWorks SN6000











































































































































































































































































































































Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands

HP StorageWorks SN6000, Command Line Interface Manual

Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands