HP StorageWorks SN6000 Command Line Interface Manual Download Page 106

Page: 106 / 330

106 Call Home Configuration

Call Home messages

The Call Home service generates email messages for the specified event severity level and the following

switch actions:

•

Switch comes online

•

Switch goes offline

•

Reboot

•

Power up

•

Power down

•

SFP failure

NOTE:

For a power-down event, if the switch is forced to power down before the message is sent to the

SMTP server, no message will be transmitted.

When a qualifying switch action or event occurs, an email message is created and placed in the Call

Home queue to be sent to the active SMTP server. You can monitor activity in the queue using the

callhome queue stats

command. You can also clear the queue of email messages using the

callhome queue clear

command.

There are three email message formats: full text, short text, and Tsc1. The full-text format contains the switch

and event information, plus the contact information from the Call Home profile and SNMP configurations.

The short-text and Tsc1 formats contain basic switch and event information; Tsc1 is formatted for automated

parsing.
The following is an example of a short-text email:

From: [email protected] [mailto:[email protected]]

Sent: Wednesday, July 25, 2007 5:03 PM

Subject: [CallHome: Test] Alarm generated on Switch_8

SwitchName: Switch_8_83.215

SwitchIP: 10.20.30.40

SwitchWWN: 10:00:00:c0:dd:0c:66:f2

Level: Alarm

Text: CALLHOME TEST PROFILE MESSAGE

ID: 8B00.0002

Time: Wed Jul 25 17:02:40.343 CDT 2007

Summary of Contents for StorageWorks SN6000











































































































































































































































































































































Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands

HP StorageWorks SN6000, Command Line Interface Manual

Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands