HP StorageWorks SN6000 Command Line Interface Manual Download Page 117

Page: 117 / 330

HP StorageWorks SN6000 Fibre Channel Switch Command Line Interface Guide 117

12 Simple Network Management Protocol Configuration

The Simple Network Management Protocol (SNMP) provides for the management of the switch through

third-party applications that use SNMP. Security consists of a

ReadCommunity

string and a

WriteCommunity

string that serve as passwords that control read and write access to the switch. These

strings are set at the factory to well-known defaults and should be changed if SNMP is to be enabled. The

switch supports SNMP version 3 in the CLI, which is disabled by default.

Managing the SNMP service

You control the SNMP service

SNMPEnabled

parameters through the

set setup snmp

set setup services

commands. See ”

Modifying the SNMP configuration

” (page 119).

To enable SNMP, enter the

set setup services

command, as shown in the following example:

SN6000 FC Switch #> admin start

SN6000 FC Switch (admin) #> set setup services

A list of attributes with formatting and current values will follow.

Enter a new value or simply press the ENTER key to accept the current value.

If you wish to terminate this process before reaching the end of the list

press 'q' or 'Q' and the ENTER key to do so.

PLEASE NOTE:

-----------

* Further configuration may be required after enabling a service.

* If services are disabled, the connection to the switch may be lost.

* When enabling SSL, please verify that the date/time settings

on this switch and the workstation from where the SSL connection

will be started match, and then a new certificate may need to be

created to ensure a secure connection to this switch.

TelnetEnabled (True / False) [True ]

SSHEnabled (True / False) [False]

GUIMgmtEnabled (True / False) [True ]

SSLEnabled (True / False) [False]

EmbeddedGUIEnabled (True / False) [True ]

SNMPEnabled (True / False) [True ]

NTPEnabled (True / False) [False]

CIMEnabled (True / False) [False]

FTPEnabled (True / False) [True ]

MgmtServerEnabled (True / False) [True ]

CallHomeEnabled (True / False) [True ]

Do you want to save and activate this services setup? (y/n): [n]

You can display the

SNMPEnabled

parameters using the

show setup snmp

show setup services

commands.

Summary of Contents for StorageWorks SN6000











































































































































































































































































































































Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands

HP StorageWorks SN6000, Command Line Interface Manual

Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands