HP StorageWorks SN6000 Command Line Interface Manual Download Page 227

Page: 227 / 330

HP StorageWorks SN6000 Fibre Channel Switch Command Line Interface Guide 227

The following is an example of the

set setup system logging

command:

SN6000 FC Switch (admin) #> set setup system logging

A list of attributes with formatting and current values will follow.

Enter a new value or simply press the ENTER key to accept the current
value.

If you wish to terminate this process before reaching the end of the list

press 'q' or 'Q' and the ENTER key to do so.

Current Values:

LocalLogEnabled True

RemoteLogEnabled False

RemoteLogHostAddress 10.0.0.254

New Value (press ENTER to accept current value, 'q' to quit, 'n' for none):

LocalLogEnabled (True / False) :

RemoteLogEnabled (True / False) :

RemoteLogHostAddress (hostname, IPv4, or IPv6 Address) :

Do you want to save and activate this system setup? (y/n): [n]

The following is an example of the

set setup system ntp

command:

SN6000 FC Switch (admin) #> set setup system ntp

A list of attributes with formatting and current values will follow.

Enter a new value or simply press the ENTER key to accept the current
value.

If you wish to terminate this process before reaching the end of the list

press 'q' or 'Q' and the ENTER key to do so.

Current Values:

NTPClientEnabled False

NTPServerDiscovery Static

NTPServerAddress 10.20.10.10

New Value (press ENTER to accept current value, 'q' to quit, 'n' for none):

NTPClientEnabled (True / False) :

NTPServerDiscovery (1=Static, 2=Dhcp, 3=Dhcpv6) :

NTPServerAddress (hostname, IPv4, or IPv6 Address) :

Do you want to save and activate this system setup? (y/n): [n]

Summary of Contents for StorageWorks SN6000











































































































































































































































































































































Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands

HP StorageWorks SN6000, Command Line Interface Manual

Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands