manualshive.com logo in svg

HP StorageWorks SN6000, Command Line Interface Manual

The HP StorageWorks SN6000 offers efficient and reliable storage capabilities for your business needs. Enhance your productivity with this high-performance storage solution. For easy installation and guidance, be sure to download the free User Manual from manualshive.com, providing step-by-step instructions and essential information to optimize your experience.

Share
Download
background image

HP StorageWorks SN6000 Fibre Channel Switch Command Line Interface Guide 233

show alarm

Description

Displays the alarm log and session output stream display setting.

Authority

None

Syntax

show alarm

settings

Operands

settings

Displays the status of the parameter that controls the display of alarms in the session output 

stream. This parameter is set using the 

set alarm

 command.

Notes

The alarm log is cleared when the switch is reset or power-cycled.

Examples

The following is an example of the 

show alarm

 command:

SN6000 FC Switch #> show alarm

  [1][Fri Jan 19 13:50:26.508 UTC 2007][A][1004.000F][Port: 4][Eport 
Isolating 
due to Merge Zone Failure]

  [2][Fri Jan 19 13:50:26.513 UTC 2007][A][1004.0030][Topology change, lost 
route to switch with domain ID 1]

  [3][Sun Jan 21 07:59:28.677 UTC 2007][A][1004.0030][Topology change, lost 
route to switch with domain ID 99]

  [4][Sun Jan 21 07:59:29.367 UTC 2007][A][1004.0030][Topology change, lost 
route to switch with domain ID 101]

The following is an example of the 

show alarm settings

 command:

SN6000 FC Switch #> show alarm settings

  Current settings for alarm

  --------------------------

  display  ON

Summary of Contents for StorageWorks SN6000











































































































































































































































































































































Reviews:

No comments

Related manuals for StorageWorks SN6000

thomann the t.racks DS2418 User Manual preview
the t.racks DS2418
Brand: thomann Pages: 8
Dewenwils HCRA50A Instruction Manual preview
HCRA50A
Brand: Dewenwils Pages: 2
FuelTech FT550 Quick Start Manual preview
FT550
Brand: FuelTech Pages: 4
Speaka Professional SP-1676616 Operating Instructions preview
SP-1676616
Brand: Speaka Professional Pages: 4
Speaka Professional 41 91 53 Operating Instructions preview
41 91 53
Brand: Speaka Professional Pages: 4
Speaka Professional HDMIV-IPSO100 Operating Instructions Manual preview
HDMIV-IPSO100
Brand: Speaka Professional Pages: 8
CommScope ION-19P Manual preview
ION-19P
Brand: CommScope Pages: 43
Kinivo HS180 User Manual preview
HS180
Brand: Kinivo Pages: 10
peerless-AV ACC800 Manual preview
ACC800
Brand: peerless-AV Pages: 12
LINK-MI LM-SP142M Quick Start Manual preview
LM-SP142M
Brand: LINK-MI Pages: 4
LINK-MI MX41-4K2K Operating Instructions preview
MX41-4K2K
Brand: LINK-MI Pages: 4
PureTools PT-SP-HD14DA User Manual preview
PT-SP-HD14DA
Brand: PureTools Pages: 20
3M ECAM-20 MM-D Instructions Manual preview
ECAM-20 MM-D
Brand: 3M Pages: 18
MacArtney OptoLink A-CCP Handling Instructions preview
OptoLink A-CCP
Brand: MacArtney Pages: 4
Cablematic S300 User Manual preview
S300
Brand: Cablematic Pages: 11
Hall Research Technologies UHBX-3S User Manual preview
UHBX-3S
Brand: Hall Research Technologies Pages: 12
natus Nicolet EDX Instructions For Use Manual preview
Nicolet EDX
Brand: natus Pages: 132
Lapp Group EPIC POWERLOCK Assembly Instruction Manual preview
EPIC POWERLOCK
Brand: Lapp Group Pages: 13

Brands by name

Popular brands

Load more brands