HP StorageWorks SN6000 Command Line Interface Manual Download Page 77

Page: 77 / 330

HP StorageWorks SN6000 Fibre Channel Switch Command Line Interface Guide

Modifying the zoning database

To modify the non-volatile zoning database:

Enter the

admin start

command.

SN6000 FC Switch #> admin start

An Admin session prevents other accounts from making changes at the same time through Telnet,

QuickTools, Enterprise Fabric Management Suite, or any other management application.

Take one of the following actions:
• To open a Zoning Edit session, enter the

zoning edit configured

command. The Zoning Edit

session provides access to the

zoneset

zone

alias

, and

zoning

commands with which you

make modifications to the zoning database

SN6000 FC Switch (admin) #> zoning edit

SN6000 FC Switch (admin-zoning)#> zoneset . . .

SN6000 FC Switch (admin-zoning)#> zone . . .

SN6000 FC Switch (admin-zoning)#> alias . . .

SN6000 FC Switch (admin-zoning)#> zoning . . .

• To modify the temporary merged zone set (if one exists), enter the

zoning edit merged

command.

SN6000 FC Switch (admin) #> zoning edit merged

When you are finished making changes:
• To save the changes and close the Zoning Edit session, enter the

zoning save

command.

SN6000 FC Switch (admin-zoning)#> zoning save

• To close the Zoning Edit session without saving changes, enter the

zoning cancel

command.

SN6000 FC Switch (admin-zoning)#> zoning cancel

To activate the changes to the active zone set, enter the

zoneset activate

command.

SN6000 FC Switch (admin)#> zoneset activate zoneset_1

The active zone set is propagated throughout the fabric.

When you are finished making changes to the switch, enter the

admin end

command to release the

Admin session for other administrators.

SN6000 FC Switch (admin)#> admin end

To remove all zoning database objects (aliases, zones, and zone sets) and restore the zoning database to

its factory state, enter the

reset zoning

command, as shown in the following example:

SN6000 FC Switch (admin) #> reset zoning

Saving the active and merged zone sets

You can save the active zone set and merged zone set to the non-volatile zoning database. To save the

active zone set, enter the

zoning active capture

command, as shown in the following example:

SN6000 FC Switch (admin) #> zoning active capture

This command will overwrite the configured zoning database in NVRAM.

Please confirm (y/n): [n] y

The active zoning database has been saved.

To the save the merged zone set, enter the

zoning merged capture

command, as shown in the

following example:

SN6000 FC Switch (admin) #> zoning merged capture

This command will overwrite the configured zoning database in NVRAM.

Please confirm (y/n): [n] y

The merged zoning database has been saved.

Summary of Contents for StorageWorks SN6000











































































































































































































































































































































Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands

HP StorageWorks SN6000, Command Line Interface Manual

Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands