HP StorageWorks SN6000 Command Line Interface Manual Download Page 63

Page: 63 / 330

HP StorageWorks SN6000 Fibre Channel Switch Command Line Interface Guide

NOTE:

Although transparent routing can be configured with the CLI, the QuickTools web applet and

Enterprise Fabric Management Suite are designed to simplify the configuration process. See the

StorageWorks SN6000 Fibre Channel Switch QuickTools Switch Management User Guide

and the

StorageWorks 8/20q and SN6000 Fibre Channel Switch Enterprise Fabric Management Suite User

Guide

To configure transparent routing:

Determine what devices on the local fabric require access to devices on the remote fabric. Local devices

must be attached directly to the SN6000 Fibre Channel Switch. In this example, the device WWNs are

as follows:
• Local device: 21:00:00:e0:8b:0e:d3:59
• Remote device: 22:00:00:04:cf:a8:7f:2d

Configure one or more TR_Ports on the local SN6000 Fibre Channel Switch:

SN6000 FC Switch #>

admin start

SN6000 FC Switch (admin) #>

config edit

SN6000 FC Switch (admin-config) #>

set config port 1

A list of attributes with formatting and current values will follow.

Enter a new value or simply press the ENTER key to accept the current value.

If you wish to terminate this process before reaching the end of the list

press 'q' or 'Q' and the ENTER key to do so.

Configuring Port Number: 1

------------------------

AdminState (1=Online, 2=Offline, 3=Diagnostics, 4=Down) [Online]

LinkSpeed (1=1Gb/s, 2=2Gb/s, 4=4Gb/s, 8=8Gb/s, A=Auto) [Auto ]

PortType (GL, G, F, FL, TR) [GL ]

SymPortName (string, max=32 chars) [Port1 ]

Finished configuring attributes.

This configuration must be saved (see config save command) and

activated (see config activate command) before it can take effect.

To discard this configuration use the config cancel command.

SN6000 FC Switch (admin-config) #>

config save

SN6000 FC Switch (admin-config) #>

config activate

Connect the TR_Port to the remote fabric. For remote HP StorageWorks B-series or C-series fabrics, the

switch to which the TR_Port is connected must support NPIV, and for B-series fabrics the interoperability

mode must be configured to InteropMode=0. Other B-series or C-series switches in the remote fabric

need not support NPIV.

Map local devices to remote devices by creating an inter-fabric zone. The inter-fabric zone contains the

port WWNs of the local device, the remote device, and the TR_Port. The name of the inter-fabric zone

begins with IFZ followed by the lowest device port WWN followed by the remaining port WWN, all

uppercase, separated by underscores (_).

Create the inter-fabric zone:

SN6000 FC Switch #>

admin start

SN6000 FC Switch (admin) #>

zoning edit

SN6000 FC Switch (admin-zoning) #>

zone create

IFZ_210000E08B0ED359_22000004CFA87F2D

Add the device and TR_Port WWNs to the inter-fabric zone:

SN6000 FC Switch (admin-zoning) #>

zone add

IFZ_210000E08B0ED359_22000004CFA87F2D 21:00:00:e0:8b:0e:d3:59
22:00:00:04:cf:a8:7f:2d 20:01:00:c0:dd:0d:53:a5

Summary of Contents for StorageWorks SN6000











































































































































































































































































































































Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands

HP StorageWorks SN6000, Command Line Interface Manual

Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands