manualshive.com logo in svg

HP StorageWorks SN6000, Command Line Interface Manual

The HP StorageWorks SN6000 offers efficient and reliable storage capabilities for your business needs. Enhance your productivity with this high-performance storage solution. For easy installation and guidance, be sure to download the free User Manual from manualshive.com, providing step-by-step instructions and essential information to optimize your experience.

Share
Download
background image

HP StorageWorks SN6000 Fibre Channel Switch Command Line Interface Guide

51

One-step firmware installation

The 

firmware install

 and 

image install

 commands download the firmware image file from an 

FTP or Trivial File Transfer Protocol (TFTP) server to the switch, unpack the image file, and perform a 

disruptive activation all in one step. The one-step installation process prompts you to enter the following 

information:

•

The file transfer protocol (FTP or TFTP)

•

IP address of the remote host

•

An account name and password on the remote host (FTP only)

•

Pathname for the firmware image file

To install the firmware:

1.

Enter the following commands to download the firmware from a remote host to the switch, install the 

firmware, and then reset the switch to activate the firmware.

SN6000 FC Switch #> admin start

SN6000 FC Switch #> firmware install

  The switch will be reset. This process will cause a
  disruption to I/O traffic.

  Continuing with this action will terminate all management
  sessions,including any Telnet sessions. When the firmware
  activation is complete, you may log in to the switch again.

  Do you want to continue? [y/n]: y

  Press 'q' and the ENTER key to abort this command.

2.

Enter your choice for the file transfer protocol with which to download the firmware image file. FTP 

requires an user account and a password; TFTP does not.

  FTP or TFTP     : ftp

3.

Enter your account name on the remote host (FTP only) and the IP address of the remote host. When 

prompted for the source file name, enter the path for the firmware image file.

  User Account    : johndoe

  IP Address      : 10.0.0.254

  Source Filename : 8.0.00.11_epc

  About to install image.  Do you want to continue? [y/n] y

4.

When prompted to install the new firmware, enter 

y

 to continue or 

n

 to cancel. Entering 

y

 will disrupt 

traffic. This is the last opportunity to cancel.

About to install image. Do you want to continue? [y/n] y
Connected to 10.20.20.200 (10.20.20.200).

220 localhost.localdomain FTP server (Version wu-2.6.1-18) ready.

5.

Enter the password for your account name (FTP only).

331 Password required for johndoe.

Password:******

230 User johndoe logged in.

The firmware will now be downloaded from the remote host to the switch, installed, and activated.

                                                                                           

Summary of Contents for StorageWorks SN6000











































































































































































































































































































































Reviews:

No comments

Related manuals for StorageWorks SN6000

Bose 839760-0010 Design Manual Supplement preview
839760-0010
Brand: Bose Pages: 3
Emerson ASCO 881 Series Instruction Manual preview
ASCO 881 Series
Brand: Emerson Pages: 6
Philips SWV3533W Specifications preview
SWV3533W
Brand: Philips Pages: 2
Handson Technology PL2303HX User Manual preview
PL2303HX
Brand: Handson Technology Pages: 7
A.Y. McDonald 6619-028 Replacement Instructions preview
6619-028
Brand: A.Y. McDonald Pages: 4
Seeing Machines MiX interface cable Installation Instructions preview
MiX interface cable
Brand: Seeing Machines Pages: 4
SIIG AV-GM06M3-S1 User Manual preview
AV-GM06M3-S1
Brand: SIIG Pages: 17
Pentair Raychem CCON25-100 Installation And Operating Instructions Manual preview
Raychem CCON25-100
Brand: Pentair Pages: 28
WBT WBT-0101 Quick Start Manual preview
WBT-0101
Brand: WBT Pages: 2
Artistic Licence Rail-Split RDM User Manual preview
Rail-Split RDM
Brand: Artistic Licence Pages: 8
UTE UH-2VE-8K User Manual preview
UH-2VE-8K
Brand: UTE Pages: 16
I-PEX CABLINE-VSF Instruction Manual preview
CABLINE-VSF
Brand: I-PEX Pages: 12
Black Box VSP-HDMI2-1X2 User Manual preview
VSP-HDMI2-1X2
Brand: Black Box Pages: 16
NEC NP1000 User Manual preview
NP1000
Brand: NEC Pages: 1169
Nauticam M24A3R140 User Manual preview
M24A3R140
Brand: Nauticam Pages: 2
Goobay 44415 User Manual preview
44415
Brand: Goobay Pages: 2
Actisense OPTO-4 Quick Start Manual preview
OPTO-4
Brand: Actisense Pages: 2
Telect WaveTrax 027-2000-4264 Installation Manual preview
WaveTrax 027-2000-4264
Brand: Telect Pages: 2

Brands by name

Popular brands

Load more brands