HP StorageWorks SN6000 Command Line Interface Manual Download Page 211

Page: 211 / 330

HP StorageWorks SN6000 Fibre Channel Switch Command Line Interface Guide 211

set setup callhome

Description

Configures the Call Home database for managing email notifications of fabric problems.

Authority

Admin session

Syntax

set setup callhome

Prompts you in a line-by-line fashion to configure the Call Home database.

Table 46

describes the

Call Home configuration attributes.

Table 46

Call Home service configuration attributes

Parameter

Description

PrimarySMTPServerAddr

IP address (version 4 or 6) or DNS host name of the

primary SMTP server. The default is 0.0.0.0.

PrimarySMTPServerPort

Service port number that the primary SMTP server is

monitoring for SMTP agents. The default is

PrimarySMTPServerEnabled

Enables (

True

) or disables (

False

) the primary SMTP

server. The default is

False

SecondarySMTPServerAddr

IP address (version 4 or 6) or DNS host name of the

secondary SMTP server. The default is 0.0.0.0.

SecondarySMTPServerPort

Service port number that the secondary SMTP server is

monitoring for SMTP agents. The default is

SecondarySMTPServerEnabled

Enable (

True

) or disable (

False

) the secondary SMTP

server. The default is

False

ContactEmailAddress

Email address of the person to be notified to respond to

the email message. The format is

account@domain

This information is included in the email message when

the profile format is

FullText

PhoneNumber

Contact phone number to be included in the email

message text. This information is included in the email

message when the profile format is

FullText

StreetAddress

Contact street address to be included in the email

message text. This information is included in the email

message when the profile format is

FullText

FromEmailAddress

Email address that is defined as the sending address in

the

From:

field of the email message. The format is

account@domain

. This field is required. Undeliverable

messages are returned to this address unless overridden

by the

ReplayToEmailAddress

parameter.

ReplyToEmailAddress

Email address that is to receive replies to the outgoing

email message. The format is

account@domain

. This

parameter overrides the

FromEmailAddress

parameter.

ThrottleDupsEnabled

Enables (

True

) or disables (

False

) the throttling of

duplicate email messages in the message queue. When

enabled, duplicate email messages that enter the queue

within 15 seconds of the original are suppressed. The

original message is sent with a report of the number of

suppressed duplicates. The default is

True

Summary of Contents for StorageWorks SN6000











































































































































































































































































































































Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands

HP StorageWorks SN6000, Command Line Interface Manual

Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands