HP StorageWorks SN6000 Command Line Interface Manual Download Page 248

Page: 248 / 330

248 Command Reference

show interface

Description

Displays the status of the active network interfaces.

Authority

None

Syntax

show interface

Examples

The following is an example of the

show interface

command:

SN6000 FC Switch #> show interface

eth0 Link encap:Ethernet HWaddr 00:C0:DD:00:00:27

inet addr:10.20.116.131 Bcast:10.20.116.255 Mask:255.255.255.0

inet6 addr: fd70:c154:c2df:116:2c0:ddff:fe00:27/64 Scope:Global

inet6 addr: fe80::2c0:ddff:fe00:27/64 Scope:Link

UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1

RX packets:137168 errors:0 dropped:0 overruns:0 frame:0

TX packets:2194 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:1000

RX bytes:47764214 (45.5 Mb) TX bytes:328639 (320.9 Kb)

lo Link encap:Local Loopback

inet addr:127.0.0.1 Mask:255.255.255.255

inet6 addr: ::1/128 Scope:Host

UP LOOPBACK RUNNING MTU:16436 Metric:1

RX packets:3887 errors:0 dropped:0 overruns:0 frame:0

TX packets:3887 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:0

RX bytes:272461 (266.0 Kb) TX bytes:272461 (266.0 Kb)

Summary of Contents for StorageWorks SN6000











































































































































































































































































































































Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands

HP StorageWorks SN6000, Command Line Interface Manual

Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands