HP StorageWorks SN6000 Command Line Interface Manual Download Page 12

Page: 12 / 330

Command Line Interface Usage

To log in to a switch through the serial port:

Configure the workstation port with the following settings:
• 9,600 baud
• 8-bit character
• 1 stop bit
• No parity

Enter an account name and password when prompted. The default account name is

admin

, and its

password is

password

NOTE:

A switch supports a combined maximum of 19 logins or sessions, which are reserved as follows:

•

4 logins or sessions for internal applications, such as management server and Simple Network

Management Protocol (SNMP)

•

9 high priority Telnet sessions

•

6 logins or sessions for Simple SAN Connection Manager (SSCM) inband and out-of-band logins,

QuickTools logins, Enterprise Fabric Management Suite logins, and Telnet logins.

Additional logins will be refused.

Opening and closing an admin session

The command line interface (CLI) performs monitoring and configuration tasks. Commands that perform

monitoring tasks are available to all user accounts. Commands that perform configuration tasks are

available only after entering the

admin start

command to open an Admin session. A user account must

have Admin authority to enter the

admin start

command.

The following is an example of how to open and close an Admin session:

SN6000 FC Switch #> admin start

SN6000 FC Switch (admin) #>

SN6000 FC Switch (admin) #> admin end

Entering commands

The command-line completion feature makes entering and repeating commands easier.

Table 1

describes

the command-line completion keystrokes.

Table 1

Command-line completion

Keystroke

Effect

Tab

Completes the command line. Enter at least one character and press the

tab key to complete the command line. If more than one possibility

exists, press the Tab key again to display all possibilities.

Up Arrow

Scrolls backward through the list of previously entered commands.

Down Arrow

Scrolls forward through the list of previously entered commands.

Control-A

Moves the cursor to the beginning of the command line

Control-E

Moves the cursor to the end of the command line.

Control-U

Clears the command line.

Summary of Contents for StorageWorks SN6000











































































































































































































































































































































Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands

HP StorageWorks SN6000, Command Line Interface Manual

Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands