HP StorageWorks SN6000 Command Line Interface Manual Download Page 38

Page: 38 / 330

Switch Configuration

System process information

The

command displays system process information to help you determine what processes are running

and central processing unit (CPU) usage.
The column titles in the following example are:

•

PID—Process identifier

•

PPID—Parent process identifier

•

%CPU—Percentage CPU usage

•

%MEM—Percentage memory usage

•

TIME—Actual processing time

•

ELAPSED—Elapsed time since the process started

•

COMMAND—The command that initiated the process.

The following example displays current system processes.

SN6000 FC Switch #> ps

PID PPID %CPU %MEM TIME ELAPSED COMMAND

244 224 0.0 0.3 00:00:04 2-03:02:31 cns

245 224 0.0 0.3 00:00:06 2-03:02:31 ens

246 224 0.0 0.3 00:00:09 2-03:02:31 dlog

247 224 0.0 0.6 00:00:33 2-03:02:31 ds

248 224 0.3 2.8 00:09:59 2-03:02:31 mgmtApp

249 224 0.0 0.3 00:00:16 2-03:02:31 sys2swlog

251 224 0.0 0.4 00:00:06 2-03:02:30 fc2

252 224 0.0 0.6 00:00:16 2-03:02:30 nserver

253 224 0.0 0.8 00:00:08 2-03:02:30 PortApp

254 224 0.0 0.5 00:00:03 2-03:02:30 qfsApp

255 224 0.0 0.5 00:00:09 2-03:02:30 mserver

256 224 0.0 0.7 00:00:06 2-03:02:30 eport

257 224 0.0 0.6 00:00:13 2-03:02:30 zoning

282 254 0.0 0.5 00:00:00 2-03:02:26 qfsApp

284 224 0.0 0.6 00:00:08 2-03:02:26 snmpservicepath

285 282 0.0 0.5 00:00:00 2-03:02:26 qfsApp

308 224 0.0 0.8 00:00:29 2-03:02:25 cim_server

Elapsed time between resets

The

uptime

command displays the elapsed time since the switch was last reset and the reset method.

Note that a hot reset or non-disruptive firmware activation does not reset the elapsed time reported by this

command. The following example displays the time since the last reset.

SN6000 FC Switch #> uptime

Elapsed up time : 0 day(s), 2 hour(s), 28 min(s), 44 sec(s)

Reason last reset: NormalReset

Configuration information

The

show config

command displays a variety of configuration information at the port and switch levels.

In addition to the basic switch configurations, the

show config

command displays parameters that

control how data is maintained in the security and zoning databases. The

show config

command

displays the following types of information:

•

Switch configuration parameters

, page 39

•

Zoning configuration parameters

, page 39

•

Security configuration parameters

, page 40

Summary of Contents for StorageWorks SN6000











































































































































































































































































































































Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands

HP StorageWorks SN6000, Command Line Interface Manual

Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands