HP StorageWorks SN6000 Command Line Interface Manual Download Page 149

Page: 149 / 330

HP StorageWorks SN6000 Fibre Channel Switch Command Line Interface Guide 149

SecondarySecret

Hex string that is encrypted by the secondary hash and sent for

authentication. The string has the following lengths, depending on the

secondary hash function:

•

MD5 hash: 16-byte

•

SHA-1 hash: 20-byte

Binding

Domain ID of the switch to which to bind the ISL group member WWN.

This option is available only if

FabricBindingEnabled

is set to

True

using the

set config security

command.

(zero) specifies no

binding.

Table 8

ISL group member attributes (continued)

Attribute

Description

Table 9

Port group member attributes

Attribute

Description

Member

WWPN for the N_Port device that would attach to the switch. A member

cannot belong to more than one group. All loop device WWPNs must be

included in the group, otherwise the switch port will be downed, and none of

the devices will be able to log in.

Authentication

Enables (

Chap

) or disables (

None

) authentication using the Challenge

Handshake Authentication Protocol. The default is

None

PrimaryHash

The preferred hash function to use to decipher the encrypted primary secret

sent by the Port group member. The hash functions are

MD5

SHA-1

. If the

Port group member does not support the primary hash, the switch will use the

secondary hash.

PrimarySecret

Hexadecimal string that is encrypted by the primary hash for authentication

with the Port group member. The string has the following lengths depending

on the primary hash function:

•

MD5 hash: 16-byte

•

SHA-1 hash: 20-byte

SecondaryHash

Hash function to use to decipher the encrypted secondary secret sent by the

Port group member. Hash values are MD5 or SHA-1. The secondary hash is

used when the primary hash is not available on the Port group member. The

primary hash and the secondary hash cannot be the same.

SecondarySecret

Hex string that is encrypted by the secondary hash and sent for

authentication. The string has the following lengths depending on the

secondary hash function:

•

MD5 hash: 16-byte

•

SHA-1 hash: 20-byte

Table 10

MS group member attributes

Attribute

Description

Member

Port worldwide name for the N_Port device that would attach to the

switch.

CTAuthentication

Common Transport (CT) authentication. Enables (

True

) or disables

(

False

) authentication for MS group members. The default is

False

Summary of Contents for StorageWorks SN6000











































































































































































































































































































































Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands

HP StorageWorks SN6000, Command Line Interface Manual

Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands